How to Deal with your Hot Water Heater Issues?

Looking for a new heat pump hot water to install in your house? Well, you’re not alone. Heat pumps are an important part of every area. They produce a large amount of energy which can be used to heat up the environment quickly.  

By absorbing warmth from the air, the companies like Hot Water Repair in Colo Vale save your energy and money and are three times more efficient than a conventional electric heater.  

However, how does it works, and how you can deal with your hot water heater issues? Read this article to find out more about it.      

Common Hot Water Heater Issues 

Water heaters might encounter various problems including mild and severe issues. Get rid of these issues, the best way is to deal with these problems as soon as possible so you remain safe from troubleshooting issues. Let’s have a look at some common hot water heater issues.  

1- Temperature Issues 

One of the most common problems might be caused by fluctuations in your heater temperature. In cold water, thermostats might be damaged resulting in a faulty heating system.  

To solve the temperature issue, first, make sure that the main power circuit is switched off, and then check the receiving power of the thermostat. When water is warm but is unable to produce heat, you should check the hot and cold crossed connections of your thermostat. 

2- Leakage  

Sometimes it might happen that your hot water heater contains leakage either from inside or outside. The leakage may be due to various reasons. Here are some of the common reasons that can lead to heater leaking:  

  • a faulty temperature and pressure relief valve 
  • Inappropriate water pressure 
  • overheating 
  • a stuck valve 
  • a leak from nearby plumbing connection 
  • loose heating element bolts 
  • a bad gasket 
  • a leaking water tank 

Whatever is the leakage cause, the only solution to this is to lose or tight the plumbing connections first. If leakage still doesn’t stop, then check the heating elements bolts. Look if the water heater contains any corrosive or damaging element that is causing leakage.   

3- Water Issues 

Rusty water or discolored water can also highly lead to a faulty hot water heater. For this, you should check the inner lining of your tank that if it contains any corrosion or not. If yes, then check it immediately or contact a hot water repair in Colo Vale

Water issues can also be solved by fixing the anode rod and replacing your heater’s internal tank.  Moreover, you can also use a tankless water heater for proper functioning.  

4- Strange Sounds 

When your hot water heater is faulty, you will experience some unusual sounds coming from the water pipes. These gushing or gurgling sounds are a clear sign that your heater is not working properly. Sometimes trapped air in the water pipes can cause strange sounds and lead to blockage.  

5- Faulty Thermostat 

As mentioned earlier, a faulty thermostat or temperature fluctuations can also lead to improper functioning of your hot water heater system. The temperature fluctuations might be due to the following reasons: 

  • Leakage in the water tank 
  • Damaged gas control or burner assembly 
  • Reduced heater’s efficiency due to depositions 
  • Problem with the temperature-pressure relief valve. 

The Working Mechanism of Heat Pump Hot Water System 

Basically, the heat pump hot water works just like a refrigerator with the difference that instead of pumping heat out of the fridge, it pumps heat inside the water. Using electricity, it transfers the heat from air to water.  

Following are the steps that are involved in the proper working of a heat pump hot water system. Let’s have a look at them one by one. 

1- Transfer of Heat 

The first step involves the withdrawal of external air into an evaporator. The evaporator further consists of a refrigerator which passes through an evaporator and converts the liquid air into gas. Hence, it simply works like a refrigerator in a reverse cycle.  

2- Compression of Gas 

Now, the gas is allowed to compress with the help of an electric compressor. Once the gas is compressed, the temperature of the system increase and becomes warmer than the water in the tank. With the help of a small valve, it then now compresses the refrigerator and produces a large amount of heat.  

3- Condensation of Gas 

After the gas refrigerator is compressed, the hot gas is allowed to pass through a condenser. The condenser passes the heat to the water and turns it back to the liquid state. With the help of a heat exchanger, the heat is transferred from the refrigerator to the tank so it can store the water.  

4- Flow into Valve 

A Hot water repair in Colo Vale flows the liquid refrigerator into an expansion valve. The valve reduces the pressure and the system cools down immediately, the liquid refrigerator enters into the evaporator and the cycle repeats.  

As the heat has drawn away from the system, the temperature of the refrigerator has dropped automatically and it again converts into the liquid state and the heat pump cycle starts again.  

Hence, by looking at the above-mentioned causes and their solutions, you can easily solve your hot water heater issues on one hand. If not, it is always recommended to contact a professional for help.  

Final Thoughts 

A heat pump is surely a mandatory need for every house. By knowing its working mechanism and other specs, you can easily install one in your area. Remember to carefully look for specific details before finalizing any heat pump hot water system.  

Disclaimer: This is a generic Information & post; content about the services can be changed from time to time as per your requirements and contract. To get the latest and updated information, contact us today or visit our website.


Leave a Reply

Your email address will not be published. Required fields are marked *